Terms of reference for the design of the roof sample. Terms of reference for designing a house

Carry out according to the technical conditions, the requirements of the current normative documents... The project should provide for:

1.Power supply

The project should provide for the required number of distribution (trunk) electrical panels that are power supply centers for large tenants (grocery hypermarket, electronics supermarket, etc.)

2.Main switchboard (MSB)

Provide for the device of the required number of main switchboards. Each main switchboard shall have two main busbar sections with circuit breakers. Provide a section switch between the sections.

The technical characteristics of the main switchboard shall be determined by the project, use the component equipment of the IEK company or another certified one.

Main switchgear-0.4 kV cabinets must be serviced one- or two-way (to be specified by the project). In each main switchboard (ASU), it is necessary to provide a reserve of 15% of circuit breakers of outgoing lines and a reserve of 15% of free space for the possible installation of additional equipment (circuit breakers, etc.).

3.Electricity metering

Provide commercial metering of electricity on the input panels of the main switchboard with calculated three-phase meters.

4.Electric panel boards

The group boards are to be wall-mounted and floor-mounted in enclosures with a protection class of at least IP20. In technical and damp rooms, provide for the installation of boards with a protection class of at least IP44. Use circuit breakers as protection devices for group cables leaving the shields. As introductory switching devices in shields, take - knife switches. Use thermal relays as overload protection devices for motors.

To develop emergency lighting boards (ALCO). Boards should be equipped with contactors, lighting control using buttons and switches. To develop power supply boards for power outlets and working lighting (SCHRO).

To develop power supply panels for rental areas (SCHRA).

To develop power supply boards for computer outlets (SCC) for office premises.

To develop power supply panels for technological equipment (SCS).

Shields (shells) shall be provided by Schneider Electric and IEK.

Switching and protective equipment will be provided by Schneider Electric and IEK.

5. Trunk cable routes

Main cable routes should be made with hot-dip galvanized steel cable ladders and sheet cable trays or wire trays.

Route electric and low-current cables on different cable shelves or one at a time through a metal partition.

Supply trunk lines with PVC-insulated cables. Route cables openly on cable shelves. Supply cables (up to distribution boards) must have a capacity margin of 10-15%. All metal cable structures are grounded

6. Wiring

For electrical wiring, use PVC-insulated cables with copper conductors. Lay cables:

Hidden in PVC pipes behind false ceilings;

Hidden in PVC pipes in strips with subsequent termination;

Opened over cable shelves;

Opened in decorative cable ducts and baseboards (office space).

The type of cable laying in the room is determined in accordance with the draft design. Execute the electrical wiring removable.

7. Wiring and wiring products

Develop a power network for household outlets. Distribute the sockets around the premises based on the location of the technological equipment and household needs. All wiring accessories should be of the appropriate protection category, depending on the category of the room.

To connect personal computers, provide for the installation of four power outlets at workplaces, two of which must be powered from the power distribution network of computers from the corresponding ShchK boards.

8. Electric lighting

The draft provides for the following types lighting of the premises of the building: working, emergency.

The voltage of the general lighting network is 380/220 V, the voltage on the lamps is 220 V, the voltage of the repair lighting is 36 V.

To illuminate the premises, use luminaires with fluorescent lamps, halogen lamps and incandescent lamps in accordance with the purpose of the premises, architectural and technical requirements.

Along the escape routes, provide for the installation of light indicators with a stencil on the front side indicating the direction of the exit. Connect the light indicators to the emergency lighting network.

Provide a power reserve for the device of advertising design of facades, displays, showcases according to the data provided by the Customer.

Provide lighting for corridors, walkways, rooms general purpose... Lighting for tenants is not provided.

Use lighting fixtures manufactured by "Light Technologies".

Wiring accessories - manufactured by Schneider Electric and DKS.

Cable support systems - DKS.

9.Power supply of fire-fighting systems

The power supply of fire alarm systems, smoke removal and air pressure systems should be provided from the ATS section of the main switchboard, or from two from two inputs (locally, provide for the installation of an ATS device).

Lay mutually redundant cables of fire-fighting systems along different routes.

10.Grounding

Use TN-C-S type earthing system. Use a reinforced concrete base of the building as a grounding device (if necessary, make an external lightning protection circuit from a 5x40 strip). The design provides for a potential equalization system.

11.Lightning protection

Lightning protection of the building is to be performed in accordance with RD 34.21.122-87.

12.Transformer substation and main switchboard

Provide a built-in transformer substation.

Accept the following equipment:

high voltage switchgear - brand RM-6 manufactured by Schneider Electric;

low voltage switchgear - based on components (switching devices, boards, etc.) manufactured by Schneider Electric;

transformers - dry brands Trihal manufactured by Schneider Electric.

MINISTRY OF CONSTRUCTION OF THE RUSSIAN FEDERATION

ORDER

In accordance with the fifth paragraph of clause 3 of the Government decree Russian Federation dated May 12, 2017 N 563 "On the procedure and on the grounds for concluding contracts, the subject of which is the simultaneous execution of work on the design, construction and commissioning of capital construction facilities, and on amending some acts of the Government of the Russian Federation" (Collected Legislation of the Russian Federation, 2017, N 21, article 3015)

I order:

1. To approve:

a) a standard form of assignment for the design of a capital construction facility in accordance with Appendix No. 1 to this order;

b) requirements for the preparation of an assignment for the design of a capital construction facility in accordance with Appendix No. 2 to this order.

2. Control over the implementation of this order shall be entrusted to the Deputy Minister of Construction, Housing and Communal Services of the Russian Federation Kh.D. Mavliyarov.

The minister
M.A. Men

Registered
at the Ministry of Justice
Russian Federation
May 3, 2018
registration N 50960

Appendix N 1. Typical form of assignment for the design of a capital construction facility

Appendix N 1

APPROVED BY

and housing and communal services
Russian Federation
dated March 1, 2018 N 125 / pr

standard form

Assignment for the design of a capital construction facility

I. General data

II. Requirements for design solutions

III. Other design requirements

46. ​​The design assignment is accompanied by:

46.1. Urban planning plan of the land plot on which it is planned to place the object and (or) the project for the planning of the territory and the project for the land survey of the territory.

46.2. The results of engineering surveys (in their absence, the design assignment provides for the need to perform engineering surveys in the amount necessary and sufficient for the preparation of design documentation).
________________
In accordance with part 5 of article 47 of the Town Planning Code of the Russian Federation (Collected Legislation of the Russian Federation, 2005, No. 1, article 16; No. 30, article 3128; 2006, No. 1, articles 10, 21; No. 23, article 2380 ; N 31, Art. 3442; N 50, Art. 5279; N 52, Art. 5498; 2007, N 1, Art. 21; N 21, Art. 2455; N 31, Art. 4012; N 45, Art. 5417; N 46, Art. 5553; N 50, Art. 6237; 2008, N 20, Art. 2251, 2260; N 29, Art. 3418; N 30, Art. 3604, 3616; N 52, Art. 6236; 2009, No. 1, article 17; No. 29, article 3601; No. 48, article 5711; No. 52, article 6419; 2010, No. 31, article 4195, 4209; No. 48, article 6246; No. 49 , Art.6410; 2011, No. 13, Art.1688; N 17, Art.2310; N 27, Art.3880; N 29, Art.4281, 4291; N 30, Art.4563, 4572, 4590, 4591, 4594, 4605; N 49, Art. 7015, 7042; N 50, Art. 7343; 2012, N 26, Art. 3446; N 30, Art. 4171; N 31, Art. 4322; N 47, Art. 6390; 53, Art. 7614, 7619, 7643; 2013, N 9, Art. 873, 874; N 14, Art. 1651; N 23, Art. 2871; N 27, Art. 3477, 3480; N 30, Art. 4040, 4080; N 43, Art. 5452; N 52, Art. 6961, 6983; 2014, N 14, Art. 1557; N 16, Art. 1837; N 19, Art. 2336; N 26, Art. 3377, 3386, 3387; No. 30, Articles 4218, 4220, 4225; 42, Article 5615; 43, Art 5799, 5804; 48, Article 6640; 2015, No. 1, Articles 9, 11, 38, 52, 72, 86; 17, Article 2477; 27, Article 3967; 29, Articles 4339, 4342, 4350, 4378, 4389; 48, Article 6705; 2016, No. 1, Articles 22, 79; No. 26, Article 3867; 27, Articles 4301, 4302, 4303, 4305, 4306; 2017, No. 11, article 1540, No. 25, article 3595, No. 27, article 3932, No. 31, article 4740, article 4767, article 4771, article 4829; 2018, N 1, article 39, article 47, article 90, article 91).

46.3. Technical conditions for connecting an object to engineering networks (if they are absent and if they are necessary, the design assignment provides for a task for their receipt).

46.4. Available materials of the approved project for the layout of the construction site. Information about the above-ground and underground engineering structures and communications.

46.5. Decision on preliminary agreement on the location of the object (if any).

46.6. A document confirming the authority of the person approving the design assignment.

46.7. Other documents and materials that must be taken into account as initial data for the design (at the discretion of the developer (technical customer).

Appendix N 2. Requirements for the preparation of an assignment for the design of a capital construction facility

Appendix N 2

APPROVED BY
by order of the Ministry of Construction
and housing and communal services
Russian Federation
dated March 1, 2018 N 125 / pr

1. Preparation of an assignment for the design of a capital construction facility (hereinafter referred to as a design assignment) is carried out by the developer (technical customer) in accordance with the standard assignment form for the design of a capital construction facility (Appendix No. 1 to this order).

2. The draft design assignment is subject to agreement with the head of the main manager of funds federal budget in relation to the object of federal property, the main manager of the budget of the constituent entity of the Russian Federation in relation to the object state property subject of the Russian Federation or the main manager of funds local budget in relation to the object of municipal property.
________________
In accordance with paragraph 21 of the Requirements for the composition and content of the justification for investments made in investment project on the creation of a capital construction facility, in respect of which it is planned to conclude a contract, the subject of which is the simultaneous execution of works on design, construction and commissioning of a capital construction facility, approved by Decree of the Government of the Russian Federation of May 12, 2017 N 563 "On the procedure and on the grounds conclusion of contracts, the subject of which is the simultaneous execution of works on design, construction and commissioning of capital construction facilities, and on amendments to some acts of the Government of the Russian Federation "(Collected Legislation of the Russian Federation, 2017, No. 21, Article 3015).

3. The design assignment is approved by the developer (technical customer) after the technological and price audit of the investment justification.

4. The design assignment must contain the initial data sufficient for the development of design documentation for the capital construction object in accordance with the requirements of the Regulation on the composition of sections of project documentation and requirements for their content, approved by Decree of the Government of the Russian Federation of February 16, 2008 N 87 (Collected Legislation Of the Russian Federation, 2008, No. 8, Art. 744; 2009, No. 21, Art. 2576, N 52, Art. 6574; 2010, N 16, Art. 1920, N 51, Art. 6937; 2011, N 8, Art. .1118; 2012, No. 27, article 3738, No. 32, article 4571; 2013, No. 17, article 2174, No. 20, article 2478, No. 32, article 4328; 2014, No. 14, article 1627 , No. 50, Article 7125; 2015, No. 31, Article 4700, No. 45, Article 6245; 2016, No. 5, Article 698, No. 48, Article 6764; 2017, No. 6, Article 942, No. 19, Art 2843 N 21, Art 3015, N 29, Art 4368, N 38, Art 5619, N 51, Art 7839).

5. The design assignment is prepared in electronic form, except for the case specified in clause 9 of these Requirements, and approved by signing by the developer (technical customer) using an enhanced qualified electronic signature.

6. A design assignment in the form of an electronic document is prepared in the following formats:

a) doc, docx, odt - for documents with text content that does not include formulas;

b) pdf - for documents with textual content, including those containing formulas and (or) graphic images, as well as documents with graphic content.

7. Electronic document issued by the authority state power, local government body, organization, natural person in accordance with the requirements established by the legislation of the Russian Federation on urban planning activities, is attached to the design assignment in the original format.

8. In the case when the original document attached to the design assignment is issued and signed authorized body state authority, local government body or organization on hard copy, the formation of an electronic document is allowed by scanning directly from the original document (the use of copies is not allowed), which is carried out while maintaining the orientation of the original document in a resolution of 300 dpi (scale 1: 1) using the following modes:

a) "black and white" (in the absence of graphic images and (or) colored text in the document);

b) "shades of gray" (if the document contains graphic images other than color graphic images);

c) "color" or "full color rendering" (if the document contains color graphics or colored text).

If a paper document consists of two or more sheets, the electronic image of such a paper document is formed in the form of one file.

Formed electronic document signed by a strengthened qualified electronic signature the person preparing the design assignment.

9. Design assignment containing information constituting state secret, prepared on paper.



Electronic text of the document
prepared by JSC "Kodeks" and verified by:
Official Internet Portal
legal information
www.pravo.gov.ru, 03.05.2018,
N 0001201805030060

The design assignment is an integral part of the contract for the design work.

The legal basis for the preparation of the design assignment is the provision of Article 759 Civil Code Of the Russian Federation, in which it is established:

1. Under a work contract for the implementation of design and survey work the customer is obliged to transfer to the contractor the design assignment, as well as other initial data necessary for drawing up technical documentation... The assignment for the execution of design work can be prepared by the contractor on behalf of the customer. In this case, the task becomes mandatory for the parties from the moment it is approved by the customer.
2. The contractor is obliged to comply with the requirements contained in the assignment and other initial data for the performance of design and survey work, and has the right to deviate from them only with the consent of the customer».

As a rule, the Customer initially issues a Design Specification, which describes the requirements for the future structure, but in order to upload it to the expertise, it is necessary to write a Design Assignment in accordance with the requirements for its design and content. Those. usually in the Terms of Reference, the Customer prescribes General requirements before the conclusion of the contract and is written in a more free form, and the Design Assignment is written after the conclusion of the contract and describes in more detail the design object and is filled in according to the requirements for filling.

The requirements for completing the Design Assignment have changed and been supplemented several times, but since March 2018, a standard form has been in effect, approved by Order No. 125 / pr of March 1, 2018.

Typical design assignment form:

Assignment for the design of a capital construction facility

I. General data

II. Requirements for design solutions

III. Other design requirements

1. The design assignment is accompanied by:

46.1. Urban planning plan of the land plot on which it is planned to place the object and (or) the project for the planning of the territory and the project for the land survey of the territory.

46.2. The results of engineering surveys (in their absence, the design assignment provides for the need to perform engineering surveys in the amount necessary and sufficient for the preparation of design documentation).
________________
In accordance with part 5 of article 47 Urban Development Code Of the Russian Federation (Collected Legislation of the Russian Federation, 2005, No. 1, Article 16; No. 30, Article 3128; 2006, No. 1, Articles 10, 21; No. 23, Article 2380; No. 31, Article 3442; No. 50, Art.5279; N 52, Art.5498; 2007, N 1, Art.21; N 21, Art.2455; N 31, Art.4012; N 45, Art.5417; N 46, Art.5553; 50, art. 6237; 2008, no. 20, art. 2251, 2260; no. 29, art. 3418; no. 30, art. 3604, 3616; no. 52, art. 6236; 2009, no. 1, art. 17; 29, Art.3601; N 48, Art.5711; N 52, Art.6419; 2010, N 31, Art.4195, 4209; N 48, Art.6246; N 49, Art.6410; 2011, N 13 , art. 1688; N 17, art. 2310; N 27, art. 3880; N 29, art. 4281, 4291; N 30, art. 4563, 4572, 4590, 4591, 4594, 4605; N 49, art. 7015, 7042; N 50, Art. 7343; 2012, N 26, Art. 3446; N 30, Art. 4171; N 31, Art. 4322; N 47, Art. 6390; N 53, Art. 7614, 7619, 7643; 2013, N 9, Art.873, 874; N 14, Art. 1651; N 23, Art. 2871; N 27, Art. 3477, 3480; N 30, Art. 4040, 4080; N 43, Art. 5452; N 52, Art. 6961, 6983; 2014, N 14, Art. 1557; N 16, Art. 1837; N 19, Art. 2336; N 26, Art. 3377, 3386, 3387; N 30, Art. 4218, 4220, 4225; N 42, Art. 5615; N 43, Art. 5799, 5804; N 48, Article 6640; 2015, No. 1, Articles 9, 11, 38, 52, 72, 86; 17, Article 2477; 27, Article 3967; 29, Articles 4339, 4342, 4350, 4378, 4389; 48, Article 6705; 2016, No. 1, Articles 22, 79; No. 26, Article 3867; 27, Articles 4301, 4302, 4303, 4305, 4306; 2017, No. 11, article 1540, No. 25, article 3595, No. 27, article 3932, No. 31, article 4740, article 4767, article 4771, article 4829; 2018, N 1, article 39, article 47, article 90, article 91).

46.3. Technical conditions for connecting an object to engineering networks (if they are absent and if they are necessary, the design assignment provides for a task for their receipt).

46.4. Available materials of the approved project for the layout of the construction site. Information about the above-ground and underground engineering structures and communications.

46.5. Decision on preliminary agreement on the location of the object (if any).

46.6. A document confirming the authority of the person approving the design assignment.

46.7. Other documents and materials that must be taken into account as initial data for the design (at the discretion of the developer (technical customer).

The standard form of the Design Assignment in Word format can be downloaded from the link:

Requirements for the preparation of an assignment for the design of a capital construction facility:

1. The preparation of the assignment for the design of a capital construction facility (hereinafter referred to as the design assignment) is carried out by the developer (technical customer) in accordance with the standard form of the assignment for the design of a capital construction facility (Appendix No. 1 to this order).
2. The draft design assignment is subject to agreement with the head of the chief manager of federal budget funds in relation to the object of federal property, the chief manager of the budget of the constituent entity of the Russian Federation in relation to the object of state ownership of the constituent entity of the Russian Federation, or the chief manager of local budget funds in relation to the object of municipal property.
   ________________
   In accordance with clause 21 of the Requirements for the composition and content of the justification of investments made in an investment project to create a capital construction facility, in respect of which it is planned to conclude a contract, the subject of which is simultaneously the execution of works on design, construction and commissioning of a capital construction facility, approved by the decree Of the Government of the Russian Federation of May 12, 2017 N 563 "On the procedure and the grounds for concluding contracts, the subject of which is the simultaneous execution of works on the design, construction and commissioning of capital construction facilities, and on amending some acts of the Government of the Russian Federation" ( Collected Legislation of the Russian Federation, 2017, N 21, Article 3015).
3. The design assignment is approved by the developer (technical customer) after the technological and price audit of the investment justification.
4. The design assignment must contain initial data sufficient for the development of design documentation for a capital construction object in accordance with the requirements of the Regulation on the composition of sections of design documentation and requirements for their content, approved by the Government of the Russian Federation of February 16, 2008 N 87 (Collection of laws of the Russian Federation , 2008, N 8, Art.744; 2009, N 21, Art. 2576, N 52, Art. 6574; 2010, N 16, Art. 1920, N 51, Art. 6937; 2011, N 8, Art. 1118 ; 2012, N 27, Art. 3738, N 32, Art. 4571; 2013, N 17, Art. 2174, N 20, Art. 2478, N 32, Art. 4328; 2014, N 14, Art. 1627, N 50, Article 7125; 2015, No. 31, Article 4700, No. 45, Article 6245; 2016, No. 5, Article 698, No. 48, Article 6764; 2017, No. 6, Article 942, No. 19, Art 2843 N 21, Art 3015, N 29, Art 4368, N 38, Art 5619, N 51, Art 7839).
5. The design assignment is prepared in electronic form, except for the case specified in clause 9 of these Requirements, and is approved by signing by the developer (technical customer) using an enhanced qualified electronic signature.
6. A design assignment in the form of an electronic document is prepared in the following formats:

a) doc, docx, odt - for documents with text content that does not include formulas;

b) pdf - for documents with textual content, including those containing formulas and (or) graphic images, as well as documents with graphic content.

1. An electronic document issued by a public authority, local government, organization, individual in accordance with the requirements established by the legislation of the Russian Federation on urban planning activities is attached to the design assignment in the original format.
2. In the case when the original document attached to the design assignment is issued and signed by an authorized government body, local government body or organization on paper, it is allowed to generate an electronic document by scanning directly from the original document (use of copies is not allowed), which is carried out from preserving the orientation of the original document at a resolution of 300 dpi (scale 1: 1) using the following modes:

a) "black and white" (in the absence of graphic images and (or) colored text in the document);

b) "shades of gray" (if the document contains graphic images other than color graphic images);

c) "color" or "full color rendering" (if the document contains color graphics or colored text).

If a paper document consists of two or more sheets, the electronic image of such a paper document is formed in the form of one file.

The generated electronic document is signed with an enhanced qualified electronic signature of the person preparing the design assignment.

1. A design assignment containing information constituting a state secret is prepared on paper.

Terms of reference - initial documentation, which is drawn up in fulfillment of the contractual obligations of certain parties.

In this document, the customer describes in detail what the contractor must do. Indicates the technical characteristics of the created object, sets out other requirements.

What is such a document for?

In accordance with the civil legislation of the Russian Federation, the possibility of drawing up and delivering such an assignment to the performer is provided.

In particular, this is provided for by Article 774 of the Civil Code of the Russian Federation, on the basis of which, when performing scientific and technical work, the contract may provide for the obligation of the customer to prepare the above document, as well as to agree on the program and the scope of work with the contractor.

The terms of reference, as a rule, are always provided for by the terms of state contracts for the manufacture of products, performance of work, and provision of services. The parameters of the technical assignment are first indicated in the tender documentation. The person who won the competition is obliged to strictly comply with all technical parameters.

If necessary, when performing work, rendering services, by agreement of the parties, additional technical specifications may be drawn up. This is formalized in the form of additional agreements to the contract, which come into force only after approval by all parties to the contract.

Features of drawing up a task

In this case, the following parameters are indicated

The name and quantity of the supplied goods.

Delivery address.

Estimated delivery time.

Types of supplied goods, their completeness.

Requirements for the quality of goods.

Other required specifications.

In any case, the terms of reference drawn up and prepared under any contract is an integral part of it. This document is signed by all parties to the transaction and certified by seals of the organizations. The task may also have attachments in the form of pictures, drawings, other documentation or samples of supplied products.

If deliveries of products are carried out multiple times, then it can be composed as single document(assignment) and documents for each specific delivery. The terms of reference can be signed by both the sole executive bodies of organizations ( CEOs, directors) and their representatives. The powers of representatives are formalized in the form of powers of attorney.

Our website contains different kinds technical assignments. You can download them absolutely free. If necessary, we can provide a preparation service required document by personal order. Please contact us and we will definitely help you.

Terms of reference for design

1. Basis for work: Contract No. _________ dated __.__. 201_. With "_______________________________________".

2. Contractor: JSC "___________________"

3. Purpose of work: To develop technical requirements to the sound reinforcement and sound reproduction system (electroacoustics) of the object: _________________________________.

A design assignment is a mandatory part of the source documentation approved by the customer and determining the nature and scope of architectural and construction activities for the facility, including the entire complex of the customer's basic requirements and the conditions of the initial permitting documentation.

The customer of the project is responsible for the development of the design assignment. In some cases, the direct development of the assignment on behalf of the customer is carried out by the design organization.

The design assignment is signed, the necessary approvals are carried out and then approved. The required degree of agreement and approval depends on the specific requirements of the contracting company for the project documentation.

The approximate composition of the design assignment is given below.

1. The name and location of the projected enterprise, building and structure.

2. Basis for design.

3. Type of construction.

4. Staged design.

5. Requirements for variant and competitive development.

6. Special conditions for "construction.

7. The main technical and economic indicators of the facility, including capacity, productivity, production program.

8. Requirements for quality, competitiveness and environmental parameters of products.

9. Requirements for technology, enterprise regime.

10. Requirements for architectural, constructive and space-planning solutions.

11. Allocation of construction stages, requirements for the future expansion of the enterprise.

12. Requirements and conditions for the development of environmental protection measures and measures.

13. Requirements for the regime of safety and health at work.

14. Requirements for the assimilation of production.

15. Requirements for the development of civil defense engineering and technical measures and measures to prevent emergency situations.

16. Requirements for the development of a safety declaration.

17. Requirements for the implementation of experimental design and research work.

18. Composition of demonstration materials.

Together with the design assignment, the customer issues the initial materials to the design organization:

justification of investments for the construction of an object, investment concept (investment project) or feasibility study approved by the customer;

the decision of the local executive authority on the preliminary approval of the location of the facility;

the act of choosing a land plot (route) for construction and materials attached to it;

architectural and planning assignment drawn up in accordance with the established procedure;

technical conditions for connecting the projected facility to sources of supply, engineering networks and communications;

information on public discussions of decisions on the construction of the facility;

initial data on equipment, including individual production;

the necessary data on the completed research and development work related to the creation of technological processes and equipment;

inventory materials, appraisal reports and decisions of local administration bodies, on the demolition and the nature of compensation for the demolished buildings and structures;

materials received from the local. administration and bodies state supervision, including a description of the socio-economic situation, natural conditions and the state of the natural environment, data on existing sources pollution and other information in accordance with the requirements of environmental authorities, sanitary and epidemiological conditions in the construction area;

available materials of engineering surveys and surveys, dimensional drawings of existing buildings and structures, underground and surface networks and communications on the construction site;

drawings and technical characteristics of the company's products;

assignment for the development of a tender; construction documentation (if necessary);

conclusions and materials made based on the results of a survey of existing industries, structures of buildings and structures;

technological layouts of workshops, sections with specification of equipment and information about its condition, data on working conditions at workplaces;

conditions for the placement of temporary buildings and structures, hoisting-and-transport machines and mechanisms, storage sites building materials;

other materials.

The design assignment is coordinated and approved before the design begins. In multi-stage design, the design is based on an approved previous design stage.

Basic initial data for design. The amount of initial data depends on the nature of the planned construction (new construction, reconstruction, overhaul) and the composition of the projected facility.

In any case, the initial data includes:

1) approved design assignment;

2) reports on research projects related to the development of new technological processes implemented at the projected enterprise;

3) technical conditions for connecting the projected enterprise to sources of energy and water supply, transport and engineering communications;

4) data of environmental supervision authorities on the state of the atmosphere, water bodies and soils in the area of ​​the construction site;

5) catalogs of local building materials, structures, parts and semi-finished products. ... ...

The customer must provide the initial data. submit prior to design. However, often in the practice of design and survey work, the collection and preparation of most of the initial data on behalf of the customer is performed by the designer.

When designing a new capital construction facility of an enterprise associated with the development of new territories, the following are additionally required:

1) documentation collected and developed in the process of selecting and agreeing on the location of the construction site;

2) the approved act of selection of the construction site;

3) act on the allotment of a land plot.

When carrying out a project for the reconstruction of an operating enterprise, you must additionally have:

1) a description of the existing production facilities or design documentation on the basis of which these production facilities were built, indicating the additions and changes made during the construction and operation;

2) dimensional drawings of buildings and structures (if necessary);

3) conclusion on the technical condition of equipment, buildings, structures and communications.

Collection of source materials and documents is carried out by the customer. In accordance with the design contract, a designer may be involved in this work.

Special technical specifications for design. In the "Regulations on the composition of sections of project documentation and requirements for their content", approved by the Decree of the Government of the Russian Federation dated February 16, 2008, it is established that if the requirements for reliability and safety established regulatory technical documents, or such requirements are not established, the development of documentation should be preceded by the development and approval in the prescribed manner of special technical conditions (STU).

Special technical conditions (STU) are technical standards containing, in relation to a specific object, additional or missing technical requirements in the field of safety. STU reflect the features of engineering surveys, design, construction and operation of the facility. Special technical conditions (STU) are part of design documentation for a specific object. The requirements established by the STU must not contradict the mandatory requirements established by the legislation and legal acts Of the Russian Federation and applicable regulatory documents.

In design practice, there are three types of Special Design Specifications:

The development of STUs is carried out by design or research organizations on the basis of the terms of reference issued by the customer-developer. STU requirements should be based on advanced experience and modern achievements of domestic and foreign science, technology and technology. The procedure for the development and approval of special technical conditions is established by the Ministry regional development Russian Federation. ..

Staged design. The design is carried out in two stages. The first stage is the development of a document called project documentation. In order to implement in the construction process architectural, technical and technological solutions contained in the design documentation for a capital construction object, the second stage is performed - working documentation, consisting of documents in text form, working drawings, specifications of equipment, products and materials, estimates necessary for production of construction, installation and special works.